Edelbrock 2WD 350 V8 User Manual download pdf

Catalog #5630, 5631, 5640, 5641, 5650, 5651, 5655, 5656

Rev. 11/07 - AJ/mc

EDELBROCK CAT-BACK EXHAUST SYSTEM

for 1993-1994 Chevrolet/GMC Trucks, 2WD 350 V8

with Single Stock Exhaust Outlet

Catalog #5630, #5631, #5640, #5641, #5650, #5651, #5655, & #5656

INSTALLATION INSTRUCTIONS

Suggested Tools for Installation:

❑ 3/8” rachet set and 15mm, 7/16”, and 9/16” sockets

❑ 7/16”, 9/16” and 15mm wrenches

❑ Jackstands

❑ Liquid penetrant

❑ Oxy/Acetylene torch or equivalent (for removal of old system)

Application:

Side Exit Rear Exit

Pick-Up, short bed . . . . . . . . . . . . . . . . . . . . . . . #5630 . . .#5631

Pick-Up, long bed . . . . . . . . . . . . . . . . . . . . . . . #5640 . . .#5641

Pick-Up, short bed extended cab (141” W.B.). . . #5650 . . .#5651

Pick-Up, long bed extended cab (155” W.B.) . . . #5655 . . .#5656

Disassembly

1. Raise vehicle and support with the proper jackstands,

leaving the rear suspension hanging.

2. Use caution around hot exhaust systems to avoid burns.

3. Use penetrating oil on all nuts, bolts and rubber hangers.

4. Remove all nuts, bolts, and hangers from the rear of the

catalytic converter to the tail pipes.

5. Remove the old exhaust system from the rear working

forward towards the catalytic converter. Use an

Oxy/Acetylene torch to heat the junctions of the old pipes

to ease removal.

Assembly

1. Place 3” U-clamps on the outlet end of the intermediate

pipe, push the hanger into the stock rubber hanger in the

truck, and bolt the pipe to the catalytic flange.

2. Slip muffler onto the intermediate pipe and support it.

3. Attach axle pipe to muffler using two gaskets and 3/8”

nuts, bolts, and lock washers.

4. Place the muffler hanger supplied on the back side of the

pipe flange, and use the 1-1/2” x 3/8” bolt to attach it to

the middle hole through the flanges. Push it through the

stock rubber hanger and put on the 1/2” locknut. The

hanger has two holes to accommodate your height

Please study these instructions carefully before installing your new Cat-Back Exhaust System. If you have any questions or problems,

please contact our Technical Hotline at: 1-800-416-8628, 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard Time or

e-mail us at [email protected]. Please fill out and mail your warranty card.

WARNING: Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before driving!

preference. Snug the hanger to the flanges, keeping in

mind that when you have the pieces all hung, you may

have to re-adjust height. Make sure that the muffler is

level to the chassis and the hanger is perpendicular to the

muffler case. We suggest that you start with the bottom

hole.

5. Install the tailpipe assembly next, using the remaining 1-

1/4” x 3/8” nuts, bolts, washers and gaskets. Bolt the rear

hanger bracket to the flanges and insert it into the stock

hanger. Adjust the clearance to the fender (side exit

systems) or the rear bumper (rear exit systems) to a

minimum of 7/8” and tighten all fasteners.

6. The small two-hole bracket is for the final adjustment of

tail pipe-to-bumper (or fender) clearance, and may not be

needed in some applications.

7. The factory-installed bumper may vary as much as 3/4” in

height. You may want to adjust your bumper for optimum

appearance, especially with the RPM Series chrome

exhaust tips. To make room for chrome tip installation, we

suggest a minimum of 7/8” clearance from the tailpipes to

the bumper.

8. Check for clearance to body, frame, and driveline as you

tighten the system from front to rear.

9. Check for leaks and correct, if necessary.

KIT CONTENTS

Qty. Part # Description Qty. Part # Description

1 25-5507 RPM Series Muffler 1 23-1607 1.9” Extension bracket

1 25-3014 Intermediate Pipe (#5630 #& #5631) 1 23-1610 Rear muffler hanger bracket

1 25-3015 Intermediate Pipe (#5640 & #5641) 1 23-4007 Tailpipe hanger bracket

1 25-3016 Intermediate Pipe (#5650 & #5651) 2 - 1/2”-13 plated locknuts

1 25-3017 Intermediate Pipe (#5655 & #5656) 2 - 3/8”-16 x 1-1/2” plate bolts

1 25-3011 Axle Pipe Assembly 9 - 3/8”-16 x 1-1/4” plate bolts

1 25-3007 Side Outlet Tail Pipe Assemly or 11 - 3/8”-16 plated nuts

1 25-3008 Rear Outlet Tail Pipe Assembly 11 - 3/8” plated lockwashers

4 33-5400 2-1/2” two-bolt gaskets 1 - 3” U-clamp (#5655 & #5656

1 23-1606 Two-hole extension bracket have two 3” U-clamps)

1 2

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

Page 2 - WARNING!!!

Axle Pipe AssemblyRear muffler hangerbracketTailpipe hanger bracketTailpipe hangerbracketExtension bracket3/8”-16 x 1-1/4” bolt3/8”-16 x 1-1/2”bolt, n

Comments to this Manuals

No comments

Edelbrock 2WD 350 V8 User Manual

Browse online or download User Manual for For the car Edelbrock 2WD 350 V8. Edelbrock 2WD 350 V8 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Edelbrock 2WD 350 V8