Edelbrock 1935 User Manual download pdf (Page 1)

• Please study these instructions carefully before installing your new choke kit.

If you have any questions or problems, do not hesitate to contact our

Technical Hotline at:1-800-416-8628.

• CHOKE LINKAGE INSTALLATION

Edelbrock choke linkage kits are for use with Performer manifolds. Choke Kit

#1931 fits small-block Chevy Performers with divorced choke carbs #1901 &

#1902; Choke Kit #1935 fits big-block Chevy Performers with divorced choke

carbs #1901 & #1902. Figure 1 shows typical divorced choke linkage used on

Q-Jet carburetors #1901 and #1902. The metal housing which snaps in place

over the choke coil on manifold has been left off to show choke rod/coil

relationship. The metal housing should be installed on your engine, as it

retains the choke rod in the coil. The opening at the top of the metal housing

faces towards the front on small-block Chevys and to the rear on big-blocks.

• CHOKE LINKAGE ADJUSTMENT

With the engine completely cold, operate the throttle arm to unload the linkage

before checking choke blade position. Adjust the choke rod length as shown

in Figure 1 until the choke blade just closes. Bending the choke rod to shorten

it will open the choke sooner; lengthening the choke rod will make the choke

stay on longer. It is best to remove the choke rod before bending it. Do not

stretch or alter the bi-metallic spring; all adjustment can be done with the

choke rod. Be sure to install the metal housing (not shown) before driving

vehicle. After initial adjustment, you may want to fine tune the choke rod

length to suit local conditions and your driving preferences.

CHOKE LINKAGE KITS

#1931 and #1935

for Edelbrock Performer Series

Carburetors for Q-Jet Applications

Figure 1

Choke Linkage Kit installed on Edelbrock Performer manifold and carburetor

viewed from right (passenger's) side.

Bend here to adjust

choke rod length

Catalog #1931, 1935

Rev. 7/08 - AJ/mc

©2008 Edelbrock Corp.

Brochure #63-1931

• Please study these instructions carefully before installing your new choke kit.

If you have any questions or problems, do not hesitate to contact our

Technical Hotline at:1-800-416-8628.

• CHOKE LINKAGE INSTALLATION

Edelbrock choke linkage kits are for use with Performer manifolds. Choke Kit

#1931 fits small-block Chevy Performers with divorced choke carbs #1901 &

#1902; Choke Kit #1935 fits big-block Chevy Performers with divorced choke

carbs #1901 & #1902. Figure 1 shows typical divorced choke linkage used on

Q-Jet carburetors #1901 and #1902. The metal housing which snaps in place

over the choke coil on manifold has been left off to show choke rod/coil

relationship. The metal housing should be installed on your engine, as it

retains the choke rod in the coil. The opening at the top of the metal housing

faces towards the front on small-block Chevys and to the rear on big-blocks.

• CHOKE LINKAGE ADJUSTMENT

With the engine completely cold, operate the throttle arm to unload the linkage

before checking choke blade position. Adjust the choke rod length as shown

in Figure 1 until the choke blade just closes. Bending the choke rod to shorten

it will open the choke sooner; lengthening the choke rod will make the choke

stay on longer. It is best to remove the choke rod before bending it. Do not

stretch or alter the bi-metallic spring; all adjustment can be done with the

choke rod. Be sure to install the metal housing (not shown) before driving

vehicle. After initial adjustment, you may want to fine tune the choke rod

length to suit local conditions and your driving preferences.

CHOKE LINKAGE KITS

#1931 and #1935

for Edelbrock Performer Series

Carburetors for Q-Jet Applications

Figure 1

Choke Linkage Kit installed on Edelbrock Performer manifold and carburetor

viewed from right (passenger's) side.

Bend here to adjust

choke rod length

Catalog #1931, 1935

Rev. 7/08 - AJ/mc

©2008 Edelbrock Corp.

Brochure #63-1931

1

Bend here to adjust 1

Summary of Contents

Page 1 - Bend here to adjust

• Please study these instructions carefully before installing your new choke kit.If you have any questions or problems, do not hesitate to contact our

Related models: 1931

Comments to this Manuals

No comments